Reasons Your Water Heater Isn't Functioning
Reasons Your Water Heater Isn't Functioning
Blog Article
We've stumbled upon this post on What Would Cause My Electric Water Heater to Stop Working? directly below on the net and reckoned it made sense to discuss it with you in this article.
Many contemporary residences make use of an electric hot water heater for their furnace, due to its benefit and also convenience of use. However, much like any other electric devices, problems may develop with its use, all of a sudden. It can be really discouraging to awaken to a cool shower instead of a hot one or having your bath with water that isn't warm adequate or perhaps too hot. Whatever the case may be, hot water heater troubles can be fairly aggravating. Fortunately, we've made a listing of possible options to your hot water heater concerns. There are a variety of factors that could cause a lot of these issues, it could be an issue with the power supply, the electrical heating element, or the thermostat. Before doing anything, ensure you shut off the main power supply for safety. Whatever the issue is, getting it taken care of must not present way too much of a concern if you adhere to these actions:
Call An Expert:
If after changing all malfunctioning components as well as resetting your temperature level, the water heater still isn't working, you might require to speak to a specialist plumber for a specialist point of view. The issue with your heating unit could be that the cold and hot taps have been switched or it may be undersized for the amount of warm water required in your house. Whatever the situation may be, a professional plumber would help address the trouble.
Examine Your Power Supply:
As fundamental as this may seem, it is very essential. Without ample power, your hot water heater will certainly not work. So the first thing to do when your water suddenly stops working is to validate that it isn't a power trouble. Inspect if the fuse is blown out or the circuit breaker stumbled. If the breaker is the problem, simply transform it on and off once again. Change any type of broken or worn-out fuse. Examine the home appliance with power after these modifications to see if it's now functioning.
Inspect Your Thermostat:
If your water heater still isn't working or the water appearing isn't hot enough, you might need to examine the temperature setups on your upper thermostat. Ensure the breaker is switched off prior to doing anything. Open the accessibility panel as well as press the red button for temperature level reset above the thermostat. This must help warm the water. Turn the breaker back on and examine if the issue has actually been fixed.
Examine the Heating Element in the Hot Water Heater:
If it's not a power issue, after that try checking out your heating element if it is still functioning. Evaluate each of your burner to make sure the trouble isn't with any of them. If any one of them is faulty, change that part and after that examine whether the hot water is back on.
Verdict
Water heater issues are not constantly major. Most of them are due to small issues like a blown fuse or worn-out burner. Replacing the malfunctioning components ought to work. However, if you are still not able to resolve the trouble, give a call to your nearest plumber to find to get it dealt with.
What Would Cause My Electric Water Heater to Stop Working?
Your water heater is one of the most forgotten-about appliances in your home—until it quits working. Once you realize that there’s no hot water, the water heater jumps up to become the most noticeable appliance you have. No one in your family will be happy until you get the water heater fixed.
To fix an electric water heater as soon as possible, follow the troubleshooting advice discussed below.
Basic Water Heater Troubleshooting
Fortunately, you may be restore the hot water supply simply by resetting the house circuit breaker for the water heater. A tripped circuit breaker is one of the top causes of water heater failures. Shut the hot water heater breaker off then turn it back on. Give the water heater a half hour to heat up (if it’s working) and then check for hot water through one of your faucets.
If you get hot water after resetting the breaker, then the problem may be fixed if the breaker inadvertently tripped and it doesn’t continue tripping.
If the water heater breaker trips again, then you’ll likely need to have a service technician examine and repair the water heater. The service technician will check the circuit breaker and electrical supply wiring for the water heater. A short in the supply wiring or a bad circuit breaker could be causing the breaker to trip. An internal failure such as a broken heating element can also cause the breaker to continue tripping.
When resetting the water heater circuit breaker doesn’t work at all, then the water heater may be getting power while an internal water heater failure is causing the problem.
Conduct Advanced DIY Water Heater Troubleshooting
If the water heater doesn’t work after resetting the high-temperature limit switch, then you’ll need to either conduct some advanced water heater troubleshooting or have a service technician diagnose and repair the water heater failure.
Sears Technicians created a safe and highly-successful DIY advanced troubleshooting video to help you determine the cause of a water heating failure if you want to try to fix the problem yourself. Follow the advice in this video to find and fix the cause of the heating failure on your own:
The video begins with the basic troubleshooting described in the first 2 sections described above. It then goes on to guide you through checking water heater components to safely find the cause of the water heating failure.
If you get to a point in the troubleshooting where you’re not completely confident that you can safely continue, schedule a service technician to diagnose and repair the water heater.
The DIY water heater troubleshooting shown in the above video differs from the diagnosis techniques that service technicians typically use when examining a water heater to find the cause of a heating failure. Safe DIY troubleshooting doesn’t rely on live voltage checks while service technicians often use live voltage checks to quickly find the cause of water heater failures.
While many DIY’ers have been able to find the cause of water heater failures using troubleshooting advice shown in the video, some failures such as a bad circuit breaker can only be found using live voltage checks which should only be conducted by a trained service technician.
Sears Technicians have the training, tools and expertise to quickly find the cause of a water heater failure. Rely on our technicians to diagnose and repair your water heater or any other appliance in your home that quits working.
While the technician is in your home, take advantage of appliance Cleaning & Maintenance offers that the tech discusses with you. Keeping your appliances well-maintained will help them work more efficiently and last longer. Regular professional maintenance will also help prevent costly breakdowns of the appliances you depend on every day.
https://www.searshomeservices.com/blog/what-would-cause-my-electric-water-heater-to-stop-working
We were introduced to that editorial on How to Troubleshoot and Repair an Electric Water Heater through an acquaintance on a different site. Are you aware of another individual who is enthusiastic about the topic? Please feel free to promote it. I enjoy reading our article about How to Troubleshoot and Repair an Electric Water Heater.
Book A Service Call
Report this page